Wahl 392VX Manual de usuario descargar pdf (Pagina 8)

172

Self-Adhesive

Sur

face

Probe

112

Fine-Tip

Penetration

Probe

305

Miniature

Air/Gas

Probe

204CT

Paddle Probe

205

Heavy-duty

Immersion Probe

205SH

Heavy-Duty

Shielded

Immersion

Probe

155

Bolt-on

Surface

Probe

Platinum resistance temperature detectors (RTD’s) are recognized

worldwide by metrology laboratories as the most reliable standard for

measuring and comparing temperature information. Platinum provides

ong-term stability and repeatability for use as a primary standard. It

has a wide useful temperature range which makes it ideal for

laboratory and industrial applications.

Our accurate, stable platinum sensors are housed in thin wall stainless

teel shanks with low mass tips that don’t compete with the measured

object. That’s why Wahl probes have fast response, and provide an

accuracy of ±0.2°F at ice point, ±0.5% of reading thereafter.

Every probe is engineered to do a specific job in measuring surfaces,

liquids, semi-solids or gasses. Each probe has a high quality, heat-

resistant Delrin

handle, a coiled 5-foot cord and a snap-in connector

hat mates it solidly to our thermometer (exceptions noted in

descriptions below).

Every probe is calibrated at two or three temperature points on NIST

traceable secondary standards and tagged “Wahl Test Certified” with

alibration data. You can order a NIST certificate with test data for

meters and probes. See page 6.

Response time legend (to 63%):

(

Measured on flat surface at 400°F;

(2)

Measured in boiling water;

(3)

Measured in air at 10 fps

Custom Probes for Your Applications

Contact Wahl for custom-made probes to your specifications,

or let us help you design the right probe for your application.

112 Fine-Tip Penetration Probe for foods and other soft substances.

.084" diameter, 1" long tip at the end of a 2-3/4" overall length

shank. 450°F temperature limit with 3 second response

(2)

114 Heavy-Duty Piercing Probe for plastic melts, rubber, asphalt,

frozen foods, or other semi-solids. Adjustable penetration depth

limiter. 900°F temperature limit with 3.7 second response

(

4-1/2" shank length is 1/8" diameter with penetration tip.

121 Spring Articulated Straight Surface Probe for molds, dies,

platens, electronics, machine housings and all other surfaces.

Spring tip allows conformity and maximum contact to measured

surface. 900°F temperature limit; 2-second response

(1)

. 4-1/4"

shank, .25" diameter, straight tip design. Also with

-12" and -18"

shank lengths.

123U Right Angle Fast Surface Probe sealed sensor design with low

profile 90° bend tip for reaching into die and mold cavities,

electronic chassis, or other restricted areas. 900°F temperature

limit, 3-second response

(1)

. 4" shank, .250" diameter tip

124 Rigid Shank Fast Surface Probe. Sealed sensor design for

rugged applications. 4" shank length, straight tip. 900°F

temperature limit with 3 second response

(1)

145 45° Spring Articulated Surface Probe, for molds, dies, platens,

electronics, and all other surfaces. Spring tip allows conformity

and maximum contact. 4" shank and 45° tip angle.

155 Bolt-on Surface Probe for permanent installation. Used to

monitor engine or reactor surface temperatures. Copper

sheathed sensor with .218" diameter bolt hole. 10' stainless

steel covered cable and connector. 930°F; 2 second response

(

No handle.

172 Self-Adhesive Surface Probe Polymer-encased sensor in a 1.25"

x 1", pressure-sensitive adhesive patch. 10' Teflon coated cable

(no handle). Used for monitoring environmental tests, curing

cycles, and oven processing. 350°F temperature limit with 1

second response

(

201 General Purpose Immersion Probe for liquids, foods, candy,

granular materials, and semi-solids. 5.75" long X .125" diameter

shank. For measurements to 600°F with 1.7 second response

(

202 Sensitive Immersion Probe with low mass .084" diameter. 5"

long shank. Super fast response time of 1.4 seconds

(

for use in

all liquids and semi-solids. Temperature limit of 900°F.

obe listing

continued on page 9

RTD Meters

392 Series

Platinum RTD Probes

392 Series Platinum

RTD Probes

(800) 421-2853 • FAX (828) 658-0728 • www.palmerwahl.com

05/08

Calibration Ser

vices A

vailable

170 Y

ears of Continued Innovation

For 392HP Probes, simply add “HP” after Model Number

123U Right Angle

Sur

face Pr

obe

121 Spring Tip

Surface Probe

Look for the “Wahl Tested

Certified” calibration tag

on every probe.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 23 24

Comentarios a estos manuales

Sin comentarios

Wahl 392VX Manual de usuario Pagina 8

Comentarios a estos manuales

Relacionado con productos y manuales para De medición, control y control Wahl 392VX